2015-06-28 NAS4Free Beta 10.1.0.2.1702 released!
2015-06-20 NAS4Free 9.3.0.2.1681 released!
NAS4Free 9.1.0.1 and 9.2.0.1 series are end-of-life and will no longer be supported!
Don't use Extended GUI on 10.1.0.2 series.
Please we need your help with https://translations.launchpad.net/nas4free/trunk/+pots/nas4free translations

NAS4Free 9.1.0.1.690 Released (FreeBSD 9.1-RELEASE p3)

Posts only related to Release Builds, all others will be removed!
Forum rules
Set-Up GuideFAQsForum Rules
User avatar
alexey123
Moderator
Moderator
Posts: 1418
Joined: 19 Aug 2012 07:22
Location: Israel, Karmiel
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby alexey123 » 02 Mar 2013 16:22

Raul
I use 2 NICs, 1 as LAN for NAS4Free, 2 as interface for jails.

Code: Select all

# ifconfig
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 6000
        options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTATE>
        ether c8:3a:35:df:0e:78
        inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
        nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
vr0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=82808<VLAN_MTU,WOL_UCAST,WOL_MAGIC,LINKSTATE>
        ether 00:11:5b:7f:60:af
        inet 10.0.0.6 netmask 0xffffffff broadcast 10.0.0.6
        nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active


Work fine.
If I swap NIC's - any problem



Onichan wrote:Your picture that shows the properties with it at 1GB says there are a bunch of symbolic links.

You right! :!:
Home10.1.0.2 - Prescience (revision 1665) / x64-embedded on SAPPHIRE Pure Mini E350 / 8G RAM
Lab 10.1.0.2 - Prescience (revision 1665) / x64-embedded on AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ / M61PME-S2 / 2G RAM
TEST x86-embedded on Intel(R) Atom(TM) CPU D2500 @ 1.86GHz / 2G RAM

discostur
Starter
Starter
Posts: 17
Joined: 10 Jan 2013 15:24
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby discostur » 06 Mar 2013 15:21

al562 wrote:Hi Discostur,

Is it possible the logs are growing larger and you are running out of space?

Regards,
Al


Hi Al,

my partition is 364 MB and i have still 66 MB free space on it. Think that can't be the problem, or?

User avatar
al562
Moderator
Moderator
Posts: 236
Joined: 12 Dec 2012 07:02
Location: New Jersey, U.S.A.
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby al562 » 07 Mar 2013 18:50

Hi Discostur,

Well, 66MB seems adequate. The logs recycle themselves depending on your settings in WebGUI Tab> Diagnostics|Log|Settings. I guess it's possible to set a high number there. There must be some limit, but i am not sure what it is and I have never hit it. I have seen things like what you posted earlier in logs, but they have all been the result of the OS running out of space. Otherwise I have been unable to reproduce your situation, sorry.

Regards,
Al
Personal Storage- i386-full 9.1.0.1-573 on Asus P4P800-VM, 2.4Ghz P4, 512Mb RAM, Promise SATA300-TX4, 3Tb+. N4F Wiki Dev. system- i386-full 9.1.0.1-573 on 2.4GHz P4, 640MB RAM, Onboard IDE, 30Gb. Typical build- NAS4Free i386-embedded 9.1.0.1-531 Dell 0M0321 Bios: A08 09/23/2003, 2.70GHz. Plus a bunch of others and VM's running latest Beta/Nightly release.

discostur
Starter
Starter
Posts: 17
Joined: 10 Jan 2013 15:24
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby discostur » 12 Mar 2013 09:15

al562 wrote:Hi Discostur,

Well, 66MB seems adequate. The logs recycle themselves depending on your settings in WebGUI Tab> Diagnostics|Log|Settings. I guess it's possible to set a high number there. There must be some limit, but i am not sure what it is and I have never hit it. I have seen things like what you posted earlier in logs, but they have all been the result of the OS running out of space. Otherwise I have been unable to reproduce your situation, sorry.

Regards,
Al


Hm ok. However, in the WebGUI Tab -> Diagnostics, the Log is shown correct! Only if i open the logfile directly on the terminal i have the error (last log entry is from 28.2.13).
I just tried to remove the logfile manually, restart and then it seems to be ok again. I'll look at the logfile in a few days if the error returns or if not.

Thanks
Regards
Kilian

dcliff
NewUser
NewUser
Posts: 1
Joined: 11 Mar 2013 01:17
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby dcliff » 13 Mar 2013 08:11

Just bought a new HP N54L.
Using VMware I managed to install the embedded version onto a USB flash drive but it would not boot on the HP N54L
Since this box is headless, I cannot capture the error.
This USB stick does boot under VMware Fusion (using PLOP - http://www.plop.at)

The full version boots and runs well on the HP but I wanted to install the embedded version.

I then tried build 509 and this booted on my N54L and then I was able to upgrade to 636.

Not sure if there are any changes that would prevent build 636 from booting but an FYI for those trying to install on the HP microserver

BeNooL
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby BeNooL » 18 Mar 2013 18:00

Getting back to the issue I started mentioning here => viewtopic.php?p=11697#p11697

I have now tested build 636 on 2 computers (the same Opteron machine and an Intel based one) and having a USB key act as ZFS cache breaks the shutdown/reboot process.
For this test I only used options provided from within Nas4Free's GUI, using 2 USB keys: one for embedded install and the 2nd to act as ZFS cache device.

BeNooL
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby BeNooL » 25 Mar 2013 12:47

No one seems to use USB keys as cache devices or is it ?

Andrey_BAM
Starter
Starter
Posts: 16
Joined: 06 Feb 2013 20:07
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby Andrey_BAM » 18 Apr 2013 08:06

when will next, new release
NAS4Free 9.3.0.2- Nayla (revision 1556) x64-embedded
MB: ASUS C60M1-I, CPU: AMD С-60(on-board), Mem: 8GB, LAN: Realtek® 8111F(on-board), Storage: ZFS mirror (2TBx2)

davidb
Starter
Starter
Posts: 56
Joined: 05 Jul 2012 16:51
Status: Offline

Re: NAS4Free 9.1.0.1.636 Released (FreeBSD 9.1-RELEASE)

Postby davidb » 19 Apr 2013 16:33

I am sure that the next release will be when Zoon and Dayoma are satisfied with it, if you review the SVN log you can see they are actively working on it. They are doing a great job with NAS4Free and i know its easy to get ancy about the next version release. Just remember they are donating their time and efforts to this project.

For me, updating NAS4Free only happens when there is something that needs to be fixed for my particular use case. If it ain't broke...

Thanks again to the developers!!

User avatar
zoon01
Developer
Developer
Posts: 305
Joined: 20 Jun 2012 20:06
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby zoon01 » 05 May 2013 21:32

NAS4Free 9.1.0.1.687 is released today (FreeBSD 9.1-RELEASE p3)

Regards,
zoon01
System specs: NAS4Free 10.1.0.2 amd64-embedded on ASRock ALiveNF6G-GLAN - AMD Athlon X2 5050e (2.6Ghz Dual Core) - 2GB Ram 4-4-4-12 Dual Channel DDR2-800 on 8GB Transcend 600x CF, Storage: Raid5 4x Western Digital Red (WD30EFRX)

User avatar
apollo567
Site Admin
Site Admin
Posts: 445
Joined: 23 Jun 2012 05:37
Location: Ludwigshafen, Germany
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby apollo567 » 05 May 2013 22:52

zoon01 wrote:NAS4Free 9.1.0.1.687 is released today (FreeBSD 9.1-RELEASE p3)

Regards,
zoon01


Many thx for ur both work ...

updated my Test-System from 639 to 687 and reloaded the configuration from my Production-NAS running version 358.
Still no Network access, which works with version 358.....
my NAS and its development until today: viewtopic.php?f=63&t=39

User avatar
zoon01
Developer
Developer
Posts: 305
Joined: 20 Jun 2012 20:06
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby zoon01 » 05 May 2013 23:51

apollo567 wrote:
zoon01 wrote:NAS4Free 9.1.0.1.687 is released today (FreeBSD 9.1-RELEASE p3)

Regards,
zoon01


Many thx for ur both work ...

updated my Test-System from 639 to 687 and reloaded the configuration from my Production-NAS running version 358.
Still no Network access, which works with version 358.....



Please check IP address etc. I can't reproduce

Regards,
zoon01
System specs: NAS4Free 10.1.0.2 amd64-embedded on ASRock ALiveNF6G-GLAN - AMD Athlon X2 5050e (2.6Ghz Dual Core) - 2GB Ram 4-4-4-12 Dual Channel DDR2-800 on 8GB Transcend 600x CF, Storage: Raid5 4x Western Digital Red (WD30EFRX)

xuesheng
Starter
Starter
Posts: 72
Joined: 23 Jun 2012 09:56
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby xuesheng » 06 May 2013 02:11

After upgrading my x64-embedded system from 636 to 687 the system appeared to reboot OK but did not send the expected SMART 'Test' email messages. The SMART log shows both drives were detected (ada0 and ada1) but there was a problem with sending the test messages (same error for both messages):

Code: Select all

smartd[2249]: Executing test of /etc/mail/smartdreport.sh to xxx@example.com ...
smartd[2249]: Test of /etc/mail/smartdreport.sh to xxx@example.com produced unexpected output (44 bytes) to STDOUT/STDERR:
smartd[2249]: /usr/local/etc/smartd_warning.sh: not found
smartd[2249]: Test of /etc/mail/smartdreport.sh to xxx@example.com: failed (32-bit/8-bit exit status: 32512/127)

User avatar
b0ssman
Forum Moderator
Forum Moderator
Posts: 2007
Joined: 14 Feb 2013 07:34
Location: Munich, Germany
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby b0ssman » 06 May 2013 06:21

zoon01 wrote:NAS4Free 9.1.0.1.687 is released today (FreeBSD 9.1-RELEASE p3)

Regards,
zoon01


the changelog does not state what has been changed/fixed from 636.

can you give some hint?
Nas4Free 10.1.0.2.1513. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.

tron44
Starter
Starter
Posts: 33
Joined: 18 Feb 2013 19:04
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby tron44 » 06 May 2013 06:42

thx a lot!!!!
WOL works for my HP N40L

User avatar
raulfg3
Site Admin
Site Admin
Posts: 3473
Joined: 22 Jun 2012 21:13
Location: Madrid (ESPAÑA)
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby raulfg3 » 06 May 2013 07:31

b0ssman wrote:the changelog does not state what has been changed/fixed from 636.

can you give some hint?


revise changes in: http://sourceforge.net/p/nas4free/code/commit_browser
N4F 10.1.0.2.1702 on HP ProLiant DL120 G6
12GB of ECC RAM, 12x3TB disk in 3 vdev in RaidZ1 = 32TB Raw size only 22TB usable

Wiki
Last changes
Old Wiki

User avatar
apollo567
Site Admin
Site Admin
Posts: 445
Joined: 23 Jun 2012 05:37
Location: Ludwigshafen, Germany
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby apollo567 » 06 May 2013 08:02

zoon01 wrote:
apollo567 wrote:
zoon01 wrote:NAS4Free 9.1.0.1.687 is released today (FreeBSD 9.1-RELEASE p3)
Regards,
zoon01

Many thx for ur both work ...
updated my Test-System from 639 to 687 and reloaded the configuration from my Production-NAS running version 358.
Still no Network access, which works with version 358.....

Please check IP address etc. I can't reproduce
Regards,
zoon01


Hello Zoon,

perhaps I was too unprecise. I can't access my Samba share with 687 if I use the same configuration file like with my last working version 358.
I doublechecked this with my WDTV Box. Same is true there also.
Any idea or shall I send u my config file ?

Regards
Apollo
my NAS and its development until today: viewtopic.php?f=63&t=39

kko
Starter
Starter
Posts: 20
Joined: 07 May 2013 05:16
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby kko » 07 May 2013 05:26

I upgraded to 687. But now i can't edit loader.conf
I try do it via Advanced|File Editor and Advanced|File Manager. When i type /cf/boot/loader.conf in File Path and click load nothing was happen. When i use file manager loader.conf is opened normal but it wasn't to save it (loader.conf: Error saving file).
Can anyone try file editor or manager on 687?

tonyd
NewUser
NewUser
Posts: 8
Joined: 01 Nov 2012 15:20
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby tonyd » 07 May 2013 06:24

kko wrote:I upgraded to 687. But now i can't edit loader.conf
I try do it via Advanced|File Editor and Advanced|File Manager. When i type /cf/boot/loader.conf in File Path and click load nothing was happen. When i use file manager loader.conf is opened normal but it wasn't to save it (loader.conf: Error saving file).
Can anyone try file editor or manager on 687?


I have the exact same problem. When I try as root with vi, it will not save. I get the error: "Error: loader.conf: Read-only file system."

What it mounted as a read-write system before?

User avatar
raulfg3
Site Admin
Site Admin
Posts: 3473
Joined: 22 Jun 2012 21:13
Location: Madrid (ESPAÑA)
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby raulfg3 » 07 May 2013 06:27

I confirm the behaviour, Embeded file editor can't load any file, not only loader.conf, can't load system.log, or other files:

loader.conf.jpg
You do not have the required permissions to view the files attached to this post. You must LOGIN or REGISTER to view these files.
N4F 10.1.0.2.1702 on HP ProLiant DL120 G6
12GB of ECC RAM, 12x3TB disk in 3 vdev in RaidZ1 = 32TB Raw size only 22TB usable

Wiki
Last changes
Old Wiki

kko
Starter
Starter
Posts: 20
Joined: 07 May 2013 05:16
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby kko » 07 May 2013 06:43

zoon01
could you fix this problem?

User avatar
dnar
Medium User
Medium User
Posts: 102
Joined: 27 Apr 2013 09:38
Location: Perth Australia
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby dnar » 07 May 2013 09:17

raulfg3 wrote:I confirm the behaviour, Embeded file editor can't load any file, not only loader.conf, can't load system.log, or other files:

loader.conf.jpg

ditto here. I am going back to 636 for now.
NAS 1: NAS4Free 9.3.0.2 x64 embedded, Intel Core 2 E8400, 8GB, 6 x WD Green 1TB in RAIDZ2, Highpoint 2720 SAS x 8 card 6Gbps
NAS 2: NAS4Free 9.3.0.2 x64 embedded, Intel Core i3-3220, 8GB, 7 x WD Green 750GB in RAIDZ1, onboard SATA 3Gbps

Andrey_BAM
Starter
Starter
Posts: 16
Joined: 06 Feb 2013 20:07
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby Andrey_BAM » 07 May 2013 10:20

xuesheng wrote:After upgrading my x64-embedded system from 636 to 687 the system appeared to reboot OK but did not send the expected SMART 'Test' email messages. The SMART log shows both drives were detected (ada0 and ada1) but there was a problem with sending the test messages (same error for both messages):

Code: Select all

smartd[2249]: Executing test of /etc/mail/smartdreport.sh to xxx@example.com ...
smartd[2249]: Test of /etc/mail/smartdreport.sh to xxx@example.com produced unexpected output (44 bytes) to STDOUT/STDERR:
smartd[2249]: /usr/local/etc/smartd_warning.sh: not found
smartd[2249]: Test of /etc/mail/smartdreport.sh to xxx@example.com: failed (32-bit/8-bit exit status: 32512/127)

yes does not work
NAS4Free 9.3.0.2- Nayla (revision 1556) x64-embedded
MB: ASUS C60M1-I, CPU: AMD С-60(on-board), Mem: 8GB, LAN: Realtek® 8111F(on-board), Storage: ZFS mirror (2TBx2)

User avatar
dnar
Medium User
Medium User
Posts: 102
Joined: 27 Apr 2013 09:38
Location: Perth Australia
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby dnar » 07 May 2013 13:27

Fuppes continues to use higher than acceptable CPU time when idle with the 687 release.

Code: Select all

last pid:  3092;  load averages:  0.27,  0.31,  0.27  up 0+02:26:39    20:25:33
25 processes:  1 running, 24 sleeping

Mem: 43M Active, 49M Inact, 268M Wired, 14M Buf, 7328M Free
Swap:


  PID USERNAME      THR PRI NICE   SIZE    RES STATE   C   TIME   WCPU COMMAND
 2769 root           13  20    0   316M 50792K nanslp  1  55:39 22.66% fuppesd
NAS 1: NAS4Free 9.3.0.2 x64 embedded, Intel Core 2 E8400, 8GB, 6 x WD Green 1TB in RAIDZ2, Highpoint 2720 SAS x 8 card 6Gbps
NAS 2: NAS4Free 9.3.0.2 x64 embedded, Intel Core i3-3220, 8GB, 7 x WD Green 750GB in RAIDZ1, onboard SATA 3Gbps

User avatar
raulfg3
Site Admin
Site Admin
Posts: 3473
Joined: 22 Jun 2012 21:13
Location: Madrid (ESPAÑA)
Contact:
Status: Offline

Re: NAS4Free 9.1.0.1.687 Released (FreeBSD 9.1-RELEASE p3)

Postby raulfg3 » 07 May 2013 13:50

eg:

Code: Select all

last pid:  6613;  load averages:  0.68,  0.70,  0.67  up 1+06:50:59    14:49:32
24 processes:  1 running, 23 sleeping

Mem: 82M Active, 120M Inact, 1354M Wired, 826M Buf, 6346M Free
Swap:


  PID USERNAME      THR PRI NICE   SIZE    RES STATE   C   TIME   WCPU COMMAND
 3101 root            9  24    0   744M   142M nanslp  3 284:02  0.98% fuppesd
 2586 transmission    3  20    0 77076K 32972K select  0  49:25  0.00% transmission-daemon
 2706 root            1  20    0 12052K  1604K select  3   0:43  0.00% powerd
 2789 root            1  20    0 74000K 10732K select  2   0:17  0.00% smbd
N4F 10.1.0.2.1702 on HP ProLiant DL120 G6
12GB of ECC RAM, 12x3TB disk in 3 vdev in RaidZ1 = 32TB Raw size only 22TB usable

Wiki
Last changes
Old Wiki


Return to “Release Builds”

Who is online

Users browsing this forum: No registered users and 0 guests